Book With Us Today!

Everybody seems to have their own ideas when it comes to How to Install a Bathtub Yourself.

Mounting a bathtub isn't exactly brain surgery, but it does call for solid plumbing, carpentry, as well as sometimes, tiling abilities. Changing an old tub with a brand-new one is also a moderately tough job. If the old tub is readily easily accessible, the task can relocate quickly; if you need to open up a wall to eliminate the old bathtub as well as place the new tub, the task is a lot harder. In either instance, the job is within a house handyman's abilities, although you will need an assistant to leave the old tub as well as set in the brand-new one. Make certain you have certified on your own for the task and also fit attempting it. As opposed to working with a service provider to take over a halfway-completed project, it is much better to consider employing one before you start. Possibilities are you might need an expert plumber to make tube links.
This short article will certainly help you mount a new bathtub in your washroom if you have already gotten a brand-new tub as well as do not need to change the plan of your previous water pipes.
Your tools and product list need to comprise the following:

• New Bathtub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Measuring tape


• Pipeline Caps


 

Planning for the Installment

To start with, the sustaining framework provided with the bath ought to be fitted (if required) according to the manufacturer's instructions. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is important to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bath, it is likewise sensible to fit a sustaining plate under the taps unit to prevent strain on the tub.
Fit the flexible faucet connectors to the bottom of both faucets using 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet via the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. See to it you use every one of the provided washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath should now prepare to be fitted in its last placement.

Removing Old Touches

If you require to replace old taps with new ones as a part of your installment, after that the first thing you should do is disconnect the water system. After doing so, switch on the taps to drain any type of water remaining in the system. The procedure of getting rid of the existing faucets can be rather troublesome due to the restricted access that is frequently the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a fabric all set for the staying water that will originate from the pipes. As soon as the supply pipes have been eliminated, use the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from transforming throughout this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will have to be cleaned up of any kind of old securing substance.
Prior to proceeding to fit the brand-new faucets, contrast the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.

Installing the Bath tub

Using the two wooden boards under its feet, put the tub in the called for placement. The wooden boards are handy in equally spreading out the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 tiny factors.
The next objective is to make certain that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and readjusting the feet on the tub up until the spirit level reviews level.
To mount faucets, fit the bottom of the outermost flexible faucet port to the appropriate supply pipeline by making a compression join; after that do the exact same for the various other tap.
Activate the water system and check all joints as well as brand-new pipework for leaks and tighten them if required. Load the bathtub as well as also inspect the overflow electrical outlet and the typical outlet for leaks.
Lastly, deal with the bath paneling as explained in the maker's instruction manual. Tiling and securing around the bath tub needs to wait up until the bath tub has actually been used at least once as this will settle it into its final placement.

Suitable New Taps

If the tails of the new taps are plastic, then you will need a plastic adapter to prevent damages to the string. One end of the adapter fits on the plastic tail of the faucet and the other end provides a link to the current supply pipelines.
If you need to fit a monobloc, then you will call for reducing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the placing opening in the bath/basin guaranteeing that the washers remain in location between the faucet as well as the sink. Secure the faucet in place with the maker offered backnut. As soon as the faucet is securely in position, the supply pipes can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with regular tap ports. The former kind needs to be linked to the faucet finishes first, tightening up just by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.

Tiling Around the Bathtub

In the location where the bathroom meets the tile, it is needed to seal the joins with a silicone rubber caulking. This is essential as the installation can move sufficient to crack a rigid seal, causing the water to permeate the wall between the bath and the tiling, leading to complications with dampness and also feasible leakages to the ceiling below.
You can choose from a variety of coloured sealers to assimilate your components and fittings. They are marketed in tubes as well as cartridges, and can securing gaps approximately a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of drenched paper or soft rope. Keep in mind to always fill up the bathtub with water before securing, to enable the activity experienced when the bathtub is in usage. The sealant can break rather very early if you do not think about this motion before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise conveniently available on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or water resistant sticky and also cement.

A Step-by-Step Guide to Installing a Bathtub

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

 

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

 

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

Remove the Existing Bathtub

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

 

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

Choose the Right Bathtub

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

Install the Plumbing and Ledger Board

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

 

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

Install the Bathtub

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

 

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

 

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

Hook up the Plumbing

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

Install the Bathtub Surround

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

 

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

 

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

 

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

Do you really like reading about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Leave feedback below. We would be delighted to hear your views about this page. In hopes that you visit us again before long. Do you know someone else who is truly interested in the niche? Feel free to share it. Thanks a lot for your time invested reading it.

Urgent plumbing issue? Connect now.